Skip to main content

Bumper repair part 1

So my bumper has the factor chin spoiler all crumpled and there is a crack on one side. I picked up a spare bumper and decided to use this to replace. I saw that one side where it would use the bolt to mount was ripped, so I did some plastic welding to fix it.



I was going to mount this last night in class, but got caught up dealing with the roof garnish, which needed repair and work.

The idea is that now I am going to cut the bottom part of the messed up bumper and bolt it on the new bumper to make it look like a better chin spoiler... hopefully it will look good!

Comments

Post a Comment

Popular posts from this blog

I GOT A COOLBOX!!!!!!!!!!!!!!

I found out that the previa had a "cool box", which is like tiny fridge under the dash in the middle, from Toyotavantech. I have seen them only in photos and in Canadian spec previas (unsure if they were in US spec). Even our owner's manual has some mention of them. Often times, I would look at CL in Vancouver BC in hopes someone wants to sell or part a van with it. Now, I've seen a few different versions, in which I don't have the ones that are pictured below. (note, these cool box images were found on the internet). A slanted shape one  This is a cool and hot box, 3 buttons on top ------------------------------------------------------------- I've kinda looked at the cool box as a Holy Grail. 9/12/15, Saturday. After volunteering my morning at the farmer's market making boxes and putting fruits and vegetables for low income families (Phat Beets Produce!) here in Oakland, I went to go fill up gas in ...
3 comments
Read more

EGR system Clean out and Code P0401

EGR system clean and Code P0401 This is another MUST DO on the previas, especially if you are having issues and code P0401 being thrown. P0401 is "Exhaust Gas Recirculation flow insufficient detected".  Parts: - EGR intake gasket - 25628-76010 - this is on the far right side next to the exhaust. - EGR valve gasket - 25627-76010 - used for the EGR valve to the intake manifold.  -Air inlet duct gasket - 22273-76010 - this is where the air goes into the intake manifold and where   the EGR port gets plugged. 1 container of coolant I did buy a set of crow's feet and Universal joints for the Exhaust pipe. I followed Zenseeker's photo's on every single detail. If you haven't visit his website (http://zenseeker.net/Previa/PreviaMaintenance.htm), it is a treasure trove of information!!!  Zenseeker gets the credit and this would have been impossible for me to do without those pictures! **The pictures are located at the bottom of this po...
4 comments
Read more

After the previa was brought to the shop.

As I mentioned, I decided to go all out. I mean replace and hit all the issues that have been common to all Previas! Here is the van with the motor taken out:  -Cruise control lever (original was broken) -Passenger vanity mirror (original was cracked) -Grey vinyl door panels for both driver and passenger (excellent condition)(possibly get the other panels) -SADS couplers - 04374-28011 -Chain tensioner gasket - 13552-75010 -Engine mount - 12361-76042 -Engine mount - 12362-76012 -Timing chain tensioner - 13540-75020 -Timing chain - 13506-75010 -Time chain cover gaskets - 11328-75010 and 11329-75010 -Timing guide rail - 13561-76020 -Timing guide rail - 13559-76010 -Timing gear kit - CDK-014C -Oil filter mount gasket - 15692-76010 -Cylinder head gasket kit HS5890 (Victor Reinz) -rear engine oil seal - 90311-8803 -thermostat - 90916-03120 -thermostat gasket - 16325-62010 -water outlet o ring - 96761-24010 -Aisin water pump - WPT - 014 -Piston ring set ...
Post a Comment
Read more