Skip to main content

Previa Update 1/22/19

Alright.

So the Previa was straightened out and I knew that the suspension would need to be addressed.

The shop I took it initially said it was fine (I knew it would improve with pulling) but I knew it would still need to be looked at since it was tweaked.

Additionally I figure while it was there, have the door fixed. The front part of the door that meets the fender got scrapped up as you can see in this picture.



I was thinking of trying to get another door and what not.. but I figure that would take more time, and for it to be different colors (if I can find a door this color, it will likely be a different shade due to fade). Not only that, I'd have to change out the door lock and all kinds of stuff I don't have time to do.

So I asked for them to fix it while there.

------------------------------------

An additional $1400.

Almost there. I gave approval and I hope they can get the stuff right away.

Comments

Popular posts from this blog

I GOT A COOLBOX!!!!!!!!!!!!!!

I found out that the previa had a "cool box", which is like tiny fridge under the dash in the middle, from Toyotavantech. I have seen them only in photos and in Canadian spec previas (unsure if they were in US spec). Even our owner's manual has some mention of them. Often times, I would look at CL in Vancouver BC in hopes someone wants to sell or part a van with it. Now, I've seen a few different versions, in which I don't have the ones that are pictured below. (note, these cool box images were found on the internet). A slanted shape one  This is a cool and hot box, 3 buttons on top ------------------------------------------------------------- I've kinda looked at the cool box as a Holy Grail. 9/12/15, Saturday. After volunteering my morning at the farmer's market making boxes and putting fruits and vegetables for low income families (Phat Beets Produce!) here in Oakland, I went to go fill up gas in ...

EGR system Clean out and Code P0401

EGR system clean and Code P0401 This is another MUST DO on the previas, especially if you are having issues and code P0401 being thrown. P0401 is "Exhaust Gas Recirculation flow insufficient detected".  Parts: - EGR intake gasket - 25628-76010 - this is on the far right side next to the exhaust. - EGR valve gasket - 25627-76010 - used for the EGR valve to the intake manifold.  -Air inlet duct gasket - 22273-76010 - this is where the air goes into the intake manifold and where   the EGR port gets plugged. 1 container of coolant I did buy a set of crow's feet and Universal joints for the Exhaust pipe. I followed Zenseeker's photo's on every single detail. If you haven't visit his website (http://zenseeker.net/Previa/PreviaMaintenance.htm), it is a treasure trove of information!!!  Zenseeker gets the credit and this would have been impossible for me to do without those pictures! **The pictures are located at the bottom of this po...

Middle sliding door assembly fix - fixing other slider assemblies?

While I was removing the left side panel, and realized I had to remove the rear seat to get the panel out, I decided to do the same on the opposite side. I wanted to clean the junk and crap that has been sitting behind panels. This also gave me a chance to look at my sliding door track (which seemed loose) and fix the middle slider assembly. BEFORE YOU TAKE OFF THE MIDDLE ASSEMBLY, THIS WILL MAKE THE REAR OF THE SLIDING DOOR "FALL"... SO BE CAREFUL!!!!! In the video, I demonstrated that my sliding door will not close all the way unless I slammed it hard. I also seen on the forums that the middle slider has 2 posts that eventually wear out. Here is a picture from Toyotavantech's Tim The 2 posts have rollers on them and after so long, they wear out and in his picture, the post itself gets destroyed and has a "metal on metal" grinding sound. The quick fix is to nylon spacers and drill them out. Which is what I did. I couldn't get the pan...